Business is booming.

How to poke a hole in a belt 2021

To know how to make a hole in a belt, then keep reading the article

Irrespective of whatsoever method you choose to make the hole, you must first measure and indicate the hole’s location.

One inch, centre to centre, is the usual distance between belt holes—Mark the new hole position with a pen or a Sharpie using a ruler or measuring instrument. Because the aim is to remove that section of leather, it usually doesn’t matter which side of the belt you mark on.

In this article, you will get to know how to poke a hole in a belt with scissors, how to poke a hole in a Gucci belt, and how to poke a hole in a belt at home.

Read Also: What is field service management?

Ways to make a hole in a belt

When you have the choice, one of the approaches listed above is your best chance. If you’re in a hurry, the following three options will suffice.

As previously stated, merely puncturing a rough hole in a belt may cause it to rip. After making the first perforation with any of the ways below, it is advised that you take this second step: put a tiny, sharp pocket knife into the puncture and spin it around in a circular motion to bore out part of the leather, rounding out and reinforcing the hole.

Knife

When using a knife to penetrate the leather at your selected mark, the form of the blade may make puncturing the leather rugged without causing a significant incision.

A tiny, sharp pocket knife will work better than a bigger blade for this, but you’ll have to make do with what you have. Slowly slide the knife back and forth in a circular motion within the hole after delicately piercing the leather, effectively scraping away tiny portions of leather until it reaches the desired size.

Nail

Using a hammer and nail to puncture the leather to start the hole is another option. Line up the nail with your marker, hammer it through, and you’ve started your hole.

It’s worth mentioning that you’ll probably want to keep a spare piece of wood beneath the belt so you can drive the nail into anything. Also, don’t hammer too hard; otherwise, it may be difficult to remove the nail.

Scratch owl

If you have a scratch awl, a sewing awl, or even an ice pick on hand, they can help you get the hole started and keep it the appropriate size. Usually, you may drive any of these awls through the leather by hand; but, if the leather is thick or very tough, a few knocks with a mallet will suffice.

You’ll have a decent starting place for whittling off some leather with your pocket knife to produce the correctly sized, rounded hole once you’ve produced the initial hole.

It’s useful to know how to add a new notch or two to your leather belt, whether you’re putting on a few pounds over the holidays or getting healthy and losing inches with The Strenuous Life. In this article, you’ll learn about a variety of hole-punching techniques: some require specific tools, while others allow you to make do with what you have.

The first three methods presented here will demonstrate how to achieve an excellent circular belt hole with minimal effort. Then three procedures take a little more finesse but can be employed in a pinch. There’s certain to be one among these 6 approaches that match the tools you have on hand.

Regardless of whatsoever method you use to make the hole, you must first measure and indicate the location of the hole. One inch, centre to centre, is the usual distance between belt holes. Mark the location of the new hole with a pen or a Sharpie using a ruler or measuring device. Because the aim is to remove that section of leather, it usually doesn’t matter which side of the belt you mark on.

How to Make Rounded Holes in Your Belt

Although there are several methods for perforating leather, just puncturing it can cause the hole to tear during use. The rotary punch is likely the most straightforward approach. Tandy Leather makes certain leather-specific rotary punches, but you might be able to locate something usable at a standard hardware shop. Typically, you’ll want to use a #5 sized punch (the second-to-largest size) with this tool; however, depending on the buckle, you may require something larger or smaller.

 

To use the rotary punch, locate an appropriate-sized punch tube, rotate it into place, centre it over your marking, and press the handle. This tool is simple to use and may be worth buying in if you plan on punching holes frequently.

Conclusion;

It’s critical to round out the interior sides of the hole you’ve created so that you’re left with a circle large enough to accommodate the tongue of your belt buckle. This circular design can aid prevent ripping and provide the belt more strength while it’s being used frequently. The procedures below will produce a robust, neatly rounded hole in only one step.